 |
Embed module of audio stereo-signal level indocator with automatic gain/scaling adjustment StereoLM-EX ver 1.0 |
|
▶ |
|
Description
The module is designed for embedding into the equipment and to display the dynamics of changes in the amplitude of the audio frequency signal using a linear LED scale. The device allows you to evaluate the dynamism of musical audio recordings due to the built-in automatic signal level adjustment system (AGC). For this reason, the device is not designed to measure absolute voltage values.The AGC system allows you to scale the signal evenly over the full length of the scale, regardless of the actual amplitude of the signal which allows you to use the indicator in circuits after volume/tone control devices without the need for manual adjustment of the indicator when used with various sound reproducing equipment. Even with the minimum value of the set volume, the indicator will scale a small signal amplitude to the full scale. When the indicator is disconnected from one signal source and connected to another source, automatic adjustment will occur and no additional user actions will be required. To assess the difference in peak voltage values of both channels, an indication of maximum points is provided. With musical bursts, these points are "thrown up" by the main column of LEDs, and slowly "decrease" with sharp drops, which allows you to see short bursts. |
Price List
2 pcs ✔ in stock |
Key Features
- Two universal inputs/outputs that allows easy connection with sound sources and sound reproduction devices (earphones and etc).
- Two ports for LEDs tapes connection. You can use only one port (like in RX-version) or both ports if you want. Module is checking port’s connection automatically and represents indication on single or both tapes at the same time.
- Work with a large number of addressable WS2812B LEDs (64 max).
- The ability to adjust each color, brightness, noise reduction level, reverse the direction of the indication of each channel, control the mono indication using a free application (for Windows OS only).
- Simple external power supply needed (5VDC). You need to know the current consumption of your LEDs and select a suitable power supply. Maximum current is limited for 2 Ampers by built-in simple fuses.
- The module contain optocoupler with open collector/emitter output that allows to turn on/off external devices or LEDs tapes after 10 seconds audio-silence was detected.
- There is duplicate contact pads are provided on the PCB, allowing wires to be soldered instead of using connectors.
Block Diagram
Characteristics
| Type of module | Embed version A printed circuit board with components. The enclosure is not provided. LED tapes can be provided for a additional fee and are not included in the base package. | |
| Lots of LEDs supported | 64 A single tape of 64 LEDs or two tapes of 32 LEDs each. The minimum number of LEDs is 6. The number of LEDs can be reduced within the specified limits. | |
| Supported LED types | WS2812B | |
| The need to use capacitors in parallel to each LED | No With a large length of tape (large distances between LEDs) it is recommended to install capacitors according to the manufacturer's documentation of the LEDs used. | |
| Indication of the inert maximum point thrown up by the main column | Yes The color of the maximum point is always equal to the color of the last (upper) LED in the tape. | |
| Connectors for external wires | Two ports for connecting LED tapes (USB 2.0 A female). One power supply connection port (USB B micro female). Two universal audio inputs /outputs (Jack 3.5). It is also possible to solder wires to the pads. | |
| Size (Length x Width x Height), mm | 40.0 x 40.0 x 15.0 Including components on the board. | |
| The distance between the longitudinal centers of two parallel LED tapes | 20.0 mm | |
| Multidirectional physical connection of LED tapes option | No It is possible to independently adjust the display of both levels on a single LED tape. | |
| Supply voltage | from 4.3 to 5.3 Â | |
| Incorrect power supply polarity protection | Yes | |
| Current consumption | <15.0 mA Without current consumed by the LEDs. | |
| Additional power saving mode after 10 seconds of silence | Possible An optocoupler with an open collector/emitter is provided on the module board to control external devices (for example a relay interrupter for the supply of LED tapes or an amplifier). | |
| Color selection for each LED | 16 | |
| Independent color selection for stereo channel LED tapes | Yes | |
| Mono mode (indication of the level of only the left or only the right channel on a single LED tape) | Yes | |
| Automatic detection of the connection of LED tapes | Yes If the LED tape is connected to only one port then the levels of both channels are automatically displayed on single tape. If both scales are connected to two ports the levels are automatically displayed separately - each on its own separated tape. | |
| The possibility of displaying the indication of two channels on a single LED tape | Yes | |
| Disabling the indication of the inert maximum point option | Yes | |
| Adjusting the overall brightness of the LEDs option (from 0 to 100%) | Yes | |
| Reversing the indication of channels separately option | Yes Indication from top to bottom (left to right) or bottom to top (right to left). | |
| Noise reduction level selection | from 0 to 30 mV | |
| Self-configuration of module parameters | Number of LEDs, LED colors, Off/On maximum's dot indication, brightness of the LED tapes, selection of mono/stereo modes, reverse display direction, noise reduction level. A free software application is used for Windows OS 7,8,10, which allows you to configure the parameters yourself (it is enough to configure the usual connection of the module to the computer – the same as with the level indication). |
Software application: Stereo Level Meter 1.0 (StereoLM.exe)
- A friendly, intuitive interface with help tooltips provides ease of self-configuration of the device.
- Working only on Windows OS: 7, 8, 10 (x32, x64).
- Just select the necessary settings and click Start-button.
- Store various configurations in your own list, upload them at any time.
- Play the demonstration to see how the indicator will work before actually setting up the device.
Downloads
Terms of use and warranty conditions
Site administration is not responsible for the incorrect, unsafe operation of the devices by you and others, as well as for the unfair use of the information by third persons. All information provided on the website is for informational or promotional purposes. Site administration does not force you to buy and use the devices. The devices are not sent without payment, including cash on delivery - only after receiving your payment the parcel will be given to the post office. When paying you agree to transfer your personal data (full name) to Joint Stock Company "Russian Post" TIN 7724490000, which accepts, packages, transports and issues the purchased devices at the post office of your choice. Due to the inability to check the correctness of the use/operation of the devices you purchase no warranty is provided for any devices, except in cases where the warranty conditions are explicitly indicated on the full description page of the device or in the documentation for it. For the same reason and due to the impossibility of carrying out a technical examination of the integrity of the devices to find out the reasons for the failure of the devices and their electronic components (their internal plates, crystal and film structures), the devices you buy are considered technically difficult and cannot be returned or exchanged.All rights under protection © 2024 StereoLM.RU